Glass Teck Header 2013

Skilled accredited applicators are on hand to provide you with a professional service from start to finish, getting your pool in pool-party shape in a week.

STATE OF THE ART GLASS-FLAKE RESIN TECHNOLOGY

Our revolutionary glass-flake resin system has been tested and proven over many years of use in high tech industrial environments and is now available for domestic application.

There are upward of 70 layers of glass flakes in every 0.5mm of coating applied. This makes GlassTeck tougher and more resilient than a fibreglass pool. GlassTeck combines the strengthening and water resistant qualities of glass with excellent adhesion and abrasion resistance.

The layers - primer and top coat - form a permanent, indestructible chemical bond fusing with the marbellite or gunite substrate of your pool. Which means GlassTeck won’t lift, peel, crack or leak. All great news for pool owners.

GLASSTECK IS SUITABLE FOR:

Marbellite and cementitious pools.
Salt water chlorinated pools.
Conventional chlorinated pools.

Correctly applied GlassTeck will add years to the life of your pool. However, the life span of this pool lining system depends on adherence to correct application methods as well as the structural integrity of your pool. Unless application is carried out by accredited applicators, the manufacturers cannot be held responsible for any product failure.

Application 3 Application 4

GlassTeck Pool 1 GlassTeck Pool 4

GlassTeck Pool  3 GlassTeck Pool  2

GlassTeck Pool 5 GlassTeck Pool  8

GlassTeck Pool 7 GlassTeck Pool  10 GlassTeck Pool  6

SURFACE PREPERATION:

• After emptying the Pool use a hosepipe with a pressure fitting to wash the pool surface, remove any water after this and leave to dry. Use of a high-pressure washer is recommended.
• Ensure the surface is dry and dust free before application of the primer coat.
• And Top coat.
• Wear protective equipment during application, long trousers- household gloves –safety glasses.
• Mask of any area not to be coated, E.g. Lights – Mosaics- Nozzles
• If the surface of the pool is smooth to the touch, or infested with Green or Black algae, prior to coating the surface must be Acid Washed using, 1 part Hydrochloric Pool acid mixed with 2 parts water.
• After Acid washing, the surface should be HP washed and dried.

1. PRIMER. Mix contents of base and hardener together and mix with a mechanical whip for 5 minutes, apply 1 liter to 10 square meters of surface area, using a lamb’s wool roller. Do not go over any mosaics around the pool, or on steps, coat around these using a small brush.
2. Allow drying for 6 to 8 Hours at 23° C or until touch dry and can be walked on.
3. Apply first coat of GlassTeck TOP COAT. Mix contents of base and hardener together mix with a mechanical whip for 5 minutes, leave for an induction period of 30 minutes, apply to surface with a clean Mohair roller, 1 liter to 8 square meters surface area.
4. Allow overnight to cure.
5. Only after 72 hours at an average temperature of 23° C can the pool be filled.
6. Clean up general-purpose Epoxy thinners.

IMPORTANT NOTE:

Your Top Coat may have been supplied in a quantity that may require you to split into two equal quantities for Topcoats.

Thinning is not normally required, however a small amount maybe added to clean out the container which the product comes in. USE Epoxy thinners only.
This can be purchased from GlassTeck on request.

HINTS:

1. BEFORE PROCEEDING.
2. CHECK FOR THE WEATHER FORCAST IN YOUR AREA
3. USE SMALL BRUSH AROUND TILES AND MOSACIS NOT TO BE COATED.
4. MIX ALL PRODUCTS ON A PLASTIC SHEET OR INSIDE THE POOL.
5. ENSURE THE CORRECT MATERIAL COVERAGE SPREAD RATE IS APPLIED TO THE SURFACE OF THE POOL.

E&oe

 

HomeAbout usApplicationColoursContactsRHVI Group

Application
GlassCote

Navigation